Copper, brass. Collection. Antiques.
The manufacturer - a brand is absent.
Time of manufacturing: ~ the first quarter of XIX century.
The body is in the form classical pear a thickening from top to bottom blew. Inside of the body the brazier pipe with a lattice is established.
The crane of the brass cast complex(difficult) form with decorative strips, has a key of the crane simple flat wooden knob.
From two parties(sides) of the body are riveted and also are soldered two brass holders of handles of the samovar stylized under amazons bent by an arch in helmets.
To shoulders of two amazons are established by hinges brass bent as the letter "S" - representing as though « hands of amazons » - the holder of two black bone handles.
Circle in the top part of the body - the idle time little bit acting. On a cover, narrowed in an average part two knobs are established on brass racks, the boiler is absent. Copper choke in the form of a dome has two holes for adjustments of intensity of burning in brazier pipe with the help of the bent plate overlapping these apertures attached to top bone knob of the choke on the brass rack.
The rack of the basis of the cylindrical form, narrowed in an average part, is punched three-edged cuts on perimeter. The rack of the basis, extending from top to bottom is connected to the round basis having the flat bottom. In middle of the bottom of the basis it is established ash-pit on the hinge also having a latch. Three brass legs also are attached to the bottom of the basis as paws compressing spheres. Two legs in front - on the right and at the left, and one leg behind.
Material, engineering: copper, a brass, chasing, a stamp, the soldering, mount; a bone, turning, tinning.
Capacity ~ 7,5 ë.
Height: 535 mm. Width (in the widest part): 330 mm.
Condition - 10 points.

Brass. Collection. Antiques. The manufacturer - a brand is absent. Time of manufacturing: ~ 1830-1840. The body is of standard samovar form called “jar”, in the top part, close to the circle, has a groove which upper again comes back to the form of the cylinder. The crane of the cast simple form with spout and with a pith key with simple flat handle. Two lateral pattern handles in a form of ear-rings with its platforms fasten to the body, hold two cylindrical wooden handles, strapped outside by four robins. A circle simple without a relief. The cover with the top inflow has two wooden knobs on its posts. The boiler is absent. The crown of a cap form has two lines square cuts, appropriate cuts of the blew. The choke has wooden knob, similar knobs on a cover. The rack of the basis represents double blew with the drawn waist in the middle, with two lines of square cuts on each blew. The cast basis of the standard square form on four legs of sphere form. Ash-pit on a loop with a rotary latch. Material, engineering: a brass, chasing, a stamp, the soldering, mount; a tree, turning; tinning. Capacity ~ 3,0 l. Height: 445 mm. Width (in the widest part): 220 mm. A condition - 7 points.

Copper, deep oxide. Collection. Antiques.
The manufacturer - a brand is absent.
Òhe body is in a form of a sphere, with decorative belt on diameter, decorated by an ornament. . Inside the body the pipe with its own choke and small disk is established. This tube is designed to contain inside the heated weight or ice. From sides of a sphere two holders of handles with apertures under installation of handles - rings. In the top part of the body the small circle of the simple form (as a ledge), decorated is made by an ornament. On a circle the cover, under the form - continuation of a sphere of the body is established. On a cover the handle as a small sphere is established.
The brass crane, cast, complex(difficult) form, with arm-key with figured cylindrical bone quick.
To the body from four parties(sides) - four straight columns (legs) - are symmetrically soldered also decorated by horizontal and vertical strips of a length. In the bottom part - in places of fastening to the flat basis - legs look like lion's paws.
The flat basis with dredging on four parties(sides) and deflexed edges(territories), has four legs as spheres on small racks. In the middle of the basis on a small ledge the decorative miniature of the Greek vase is established.
Material, engineering: copper, a brass, polishing, chasing, a stamp, the soldering, mount, tinning, a bone, turning.
Capacity ~ 4,5 - 5,0 ë.
Height: 435 mm. Width (in the widest part): 280 mm.
Condition - 8 points (dents on the body and a cover).

Collection. Antiques. The manufacturer - a brand is absent. Time of manufacturing: ~ the first quarter of XIX century. The body in the form classical semiegg with the top cut. On the forward (obverse) party(side) of the body from one holder as a head of the ram up to an average part of the body above the crane it is soldered brass semigarland as a chain of the semicircles, sagging and in middle decorated by a flower. On the other hand of the body from other holder as a head of the ram up to an average part of the body above the crane second half of brass garland of a chain of semicircles sagging in middle with a flower in the bottom part is soldered. Two incorporate semigarlands above the crane in a flower similar two flowers in the bottom, sagging parts semigarlands. Inside the body the pipe with a lattice is established. The crane of the brass cast complex(difficult) form with decorative strips, has a key of the crane simple flat wooden handle. From two parties(sides) of the body also are soldered two brass holders of handles of a samovar stylized under heads of rams with horns upwards each. In a mouth of rams, like a bit on hinges two are established brass bent as the letter "S" the holder of the wooden handle from each party(side). Circle in the top part of the body - the idle time which is not acting. On a cover, narrowed in an average part two are established two wooden knobs on brass racks, the boiler is absent. Copper choke in the form of a dome has two apertures of adjustment of intensity of burning in a pipe with the help of the bent plate overlapping these aperture attached to top wooden knob of the choke on the brass rack. The rack of the basis of mushroom forms, narrowed in an average part, is punched oval cuts on perimeter a cap of mushroom. The rack of the basis, extending from top to bottom is connected to the square basis - a copper plate, with deflexed edges(territories). In middle of the bottom of the basis on the hinge it is established ash-pit, having a latch. Four brass legs also are attached to the bottom of the basis as spheres with acting belt in an average part each. A material, engineering: copper, a brass, a stamp, the soldering, mount; a tree, turning; tinning. Capacity ~ 6,5 L. Height: 510 mm. Width (in the widest part, handles downwards): 280 mm. Condition - 10 points.

Collection. Antiques. The manufacturer - a brand is absent. Time of manufacturing: ~ the second quarter of XIX century. The body under the form reminds a children's toy - "pyramid" and is a cone with three narrowed parts, giving to it(him) the form of three flat spheres, located one above another with narrowings a different structure between them and with the bottom conic part of the body. The cover of a complex(difficult) configuration has two bone knobs on racks, the boiler is absent. The top part of a cover has the form of a flat sphere on which perimeter triangular punching in two lines is put. A choke in a form of dome has bone knob on the rack, similar the knobs on a cover. The brass crane of the simple form with spote, is soldered to the body without patterned washer . The key of the crane has figured branch (handle) with bone quick. Two holders of handles are soldered to the second from the basis to a flat sphere with apertures under installation of handles - rings. Handles - rings in the bottom part are equipped on four bone washers and to one washer an ebony between them on each ring. The bottom, conic part of the body has applicability of the basis besides she(it) also carries out a role blew with patten cuts and the engraved figures with images of plants. To the cone bases are soldered to bottom part three cast legs in a form of the letter "S" - two - in front on the right / to the left of the crane, the third behind a samovar. In an average part of the flat bottom of the basis there is a rectangular aperture of ash-pit, along two which long parties(sides), riveted two bent a strip - directing sliding covers of the ash-pit. Material, engineering: a brass, a stamp, the soldering, an engraving, mount; a bone, turning, tinning. Capacity ~ 5,0 l. Height: 510 mm. Width (in the widest part, handles downwards): 240 mm. Condition - 10 points.

Collection. Antiques. The manufacturer - a brand is absent. Time of manufacturing: ~ middle of XIX century. Copper body as an amphora, the bottom part of the body has the form of semiegg on which walls it is executed the coiled pressed fringing dividing(sharing) convexo-concave rolling surfaces. Above semiegg part of the body is narrowed part by a mouth of an amphora on which it is executed ten vertical decorative strings. Above - the mouth of the body extends step by step passing in idle time, a smooth circle. On a flat surface of a circle it is established the choke, having a flat ring fixings it on the top aperture of the body and small handle as a musroom, representing a single whole with a choke. Two simple semioval form handles bent as the letter "S", are soldered from sides to the top cut semiegg part of the body and to its average part. On the top aperture of the body below adjusting place of a cover there is a flat round ledge in which it is established cylindrical water-strainer for a bookmark in him(it) of ground coffee, with a small ledge - giving water-strainer the form of a hat. The crane of the cast, simple form, its spout with a horn and a bell a plum is soldered to the body without patterned washer. The conic key of the crane has horizontal branch on which it is established bone knob of a ball form. In the bottom part of installation of a key in the crane is present cut - limiting a corner of turn of a key in which the metal pin is established. Below semiegg part the body narrowed in the neck of the bases which extending step by step passes the round basis of the body, fixed movably on a square support. Top of a square support - a flat plate. Three parties(sides) of a support have the parties(sides) punched on all area patten cyts - formation(education) as though the trellised parties(sides) of a support. The forward party(side) of a support has a cut, reminding fireplace. The basis of a support of the square form, step by step extending from top to bottom forms a square of the greater size. The continuous plate is soldered to a bottom of the basis of a support. Inside of a support the rectangular spirit-lamp on legs is established. Material, engineering: copper, silvering, chazing, a stamp, the soldering, mount; a bone, turning; tinning. Capacity ~ 0, 85 L. Height: 350 mm. Width (in the widest part): 210 mm. Condition - 10 points.