|
|
|
1-15 | 16-30 | 31-45 | 46-60 | 61-75 | 76-90 | 91-105 | 106-120 | 121-135 | 136-150
|
ÐÓÑ ENG |
|
|
|
A samovar - teapot. «BIG TEAPOT with the HOLE». Copper. Covered by black oxide. Collection. Antiques.
The manufacturer - a brand is absent (it is possible – made in China).
Time of manufacturing: ~ the beginning of XIX century.
Body – in a form of egg. The aperture was made for an output (exit) of the bottom part of the body perpendicularly axes the «spout-handle», horizontal part of a pipe a few acting as a cone for dimensions of the body is executed. This part of the pipe is intended for performance of function of ash-pit (blew), from a cavity formed by this part of a pipe, ashes and the rests of burning of wood also left.
Spout - is cast, brass in the form of the letter "S", narrowed to the termination (ending). At the very end has a small bell month.
Handle - is made of a copper strip and is braded by a rod; the top part of the handle, extending, like the fish tail, forms a platform, which is clamped by two copper rivets to the body; the bottom part of the handle is soldered and is clamped to the body by one rivet. Two metal rings were soldered and riveted to the top part of the body, above the spout for fastening with their help the additional wire handle used for carrying this samovar - teapot.
Cover - is a copper and demountable, has the holder of a choke, which executed of a copper strip , bent as snake, by bends rising up is established. The holder of the choke is connected with flat copper choke by thin metallic chain.
Choke - in the top part has a decorative overlay and the handle as a metal cone, in top, which deaf(indistinct) part punching as five round apertures is executed.
for fastening it(her) to cover by thin metallic chain. Round apertures which overlapping on a cover and a decorative overlay allows to adjust draft of burning in a pipe is executed on a cover and a decorative overlay. To the bottom and average part of a handle - cone for fastening the metal ring is soldered to it for the other end of a thin chain to be connected.
Pipe looks like the letter "L" where the lengthened vertical part of this letter up is narrowed, forming the cone, and the bottom horizontal part and is mentioned above the bottom part the pipe, leaving through a wall of the body outside. In the bottom of vertical part of the pipe, along an axis the «handle – spout», is little bit higher than its bend, seven tacks are soldered, carrying out a role of heat lattices.
Legs - three simple copper (asymmetrically) soldered to the bottom of the body as square slices of metal.
Material, engineering: copper, chasing, caulking, punching, a stamp, the soldering, mount; braiding by a rod, brazing, tinning, assembling.
Capacity ~ 2,0 ë.
Height: 270 mm. Width (in the widest part): 290 mm.
Condition - 8 points.
| |
|
ÐÓÑ ENG |
|
|
|
A samovar - teapot «Vase in a form of semi-egg», «GAVRILA EFIMOV,s TEAPOT». Brass. Covered by oxide. Collection. Antiques.
The manufacturer - a brand on a cover: « ÃÀÂÐÈËÀ ÅÔÈÌÎÂÚ ÂÚ ÒÓËÚ » (Gavrila Efimov in Tula).
Time of manufacturing: ~ the beginning of XIX century.
Body – in a form of cylinder at lower part passing in a hemisphere in the bottom part. The top cylindrical part of the body has the small thickening forming a simple flat round. A jug (pipe) is of standard samovar form.
Choke – simple configuration with wooden round knob on its post.
Crown – no.
Cover – punched, simple form with two round wooden knobs on their posts. Round - simple, smooth, flat.
Holder – is made of two cast holders, soldered and riveted to top and bottom part of the body. Between metallic holders the wooden handle mounted on tack and it is fastened from above and below by two figure screw-nuts.
Crane – (spout of teapot) is made by punching from a sheet of a brass, is soldered practically on all height of a forward part of the body. A pennant (folding cover on the hinge) with the small platform is soldered above the upper part of the spout for preventing hit of extraneous subjects inside of a samovar.
Ash-pit – post of the base is in cylindrical form with figure cuttings in its middle part.
Base – cast, square.
Legs – four, in a form of turned over mushrooms at corners of the base.
Ash-shut – round cover with metallic knob fastened to an additional bottom plate of the base.
Stuff, technique: brass, chasing, caulking, punching, soldering, brazing, inner tinning, assembling; wood cutting.
Capacity: ~ 0, 75 litres.
Height: 295 mm. Width (in the widest part): 230 mm.
Condition: 9 points.
| |
|
ÐÓÑ ENG |
|
|
|
A samovar "Vase a narrow wine-glass ". "WINE-GLASS NARROW BYZANTIAN ". Tombac. Collection. Antiques.
The manufacturer - a brand on a cover: at the left - two prints of one medal with rubbed an inscription and date "1882" - from above - two rubbed prints of one medal in middle - " ÂÀÑÈËIÉ ÑÒÅÏÀÍÎÂÈ×Ú ÁÀÒÀØÅÂÚ " - on the right - two prints of one medal with rubbed inscription and date: "1870".
The second brand on an obverse ledge of the figured basis - " ÂÀÑÈËIÉ ÑÒÅÏÀÍÎÂÈ×Ú ÁÀÒÀØÅÂÚ ".
Time of manufacturing: ~ last quarter of XIX century.
Body is in a form of a narrow faceted wine-glass with mirrors. The crane of the simple form, cast with a pith key and openwork decorative branch with leaves and acorns, with wooden quick. Two Byzantian vertical handles of independent double fastening everyone decorated by curls, hold on tacks two wooden figured cylindrical handles, strapped from below and from above four screw-nuts. A round is flat and decorated on all perimeter by the corrugated pattern, its dimensions is larger than edges of the body. On a cover two clamps with wooden knobs on racks and a spring valve. The crown is simple, round, with patterned cuts appropriate the cuts of the ash-pit. Choke has wooden quick on the rack. The bottom part of the body is being narrowed passes in cylindrical ash-pit, the rack of the basis is lower which is narrowed, forming its neck which smoothly extending passes in the figured basis with four openwork legs in a form of hoof. Ash-shut is of round form on a hinge with a rotary lock and it is established in the bottom part of the basis.
Material, engineering: tombac, punching, chasing, soldering, assembling; wood, turning; tinning.
Capacity ~ 4,5 L.
Height: 525 mm. Width (in the widest part): 345 mm.
Condition - 10 points. .
| |
|
ÐÓÑ ENG |
|
|
|
A samovar " Vase a wine-glass, kerosene". "GERMAN WINE-GLASS ÊÅROSENE". Nickelized brass. Collection. Antiques.
The manufacturer - a brand on the top surface of the basis: at the left - "VESUV" and on the center: "ARLT and FRICKE - BERLIN".
Time of manufacturing: ~ last quarter of XIX century, probably, the beginning of XX century.
Body is in a form of a faceted wine-glass. The crane of the simple form, cast, with a pith key and openwork decorative branch, with wooden knob. Two handles with figured platforms of fastening to the body with four figured horns upwards, are bent as the letter "S", hold two wooden handles on tacks, strapped on edges(territories) four screw-nuts. The round is of simple configuration, smooth, is decorated above by decorative hemispheres on all perimeter of the round. A cover has a foot-step upwards configuration of a hip, the unary spring valve is placed and two wooden knobs on on their posts are also established. A crown is of the simple form with figured piercing. Choke is the simple form with wooden knob on its post. The bottom part of the body is being narrowed, passes in cylindrical ash-pit, which has supporting the bottom cut a flat flange with three apertures for fastening the body to the basis by three screw-nuts. The basis represents hollow cylindrical capacity as bagel for kerosene on three, decorative legs soldered to the basis. On the right side of the basis from above are located: a jellied mouth with a cover supplied wooden knob on its post, and the adjusting screw of submission of fuel with wheel, having a decorative pattern as six-angled star. On the top part of the basis, near to the adjusting screw is present two arrows (pointers) - indexes with inscriptions on one above everyone: "AUF" and "ZU". From the right bottom side of the basis to the center the metal tube on which termination(ending) the mechanism of burning - a metal flat bowl and the high hollow cylinder is established.
Material, engineering: a brass, nickel plating, punching, chasing, soldering, mount; wood, turning; tinning.
Capacity ~ 3,5 L.
Height: 470 mm. Width (in the widest part): 285 mm.
Condition - 7 points.
| |
|
ÐÓÑ ENG |
|
|
|
Samovar " Vase in a form of a pot on a tripod brazier", a brass. Collection. Antiques.
The brand is absent.
Time of manufacturing: ~ the end of XVIII century - the beginning of XIX century.
Body is in a form of standard samovar pot. The crane is cast simple form with a key like bow and figured handle as an arch. The cover steps upwards has two wooden knobs on their posts. Two handles - as earrings are equipped with wooden handles on tacks. The ring is of simple form lugs a little the edge of the body. Choke has wooden knob on the post. The bottom part of the body has a cylindrical ledge of smaller diameter, than external diameter of the body which is intended for installation the body into upper hollow part of the base in a form of a cone. The base is under the form reminds brazier, frequently used at manufacturing the first samovars - "sbitennik". The base is executed as a cone with hollow top and deaf(indistinct) bottom cut of the truncated cone and has pierced by figured cuts - hearts and squares around all ash-blew part of the base. Three figured legs also are soldered and reverted to a flat bottom of the base. Legs have a form of hoofs - a prototype of all of the subsequent, widely widespread(distributed) samovar legs as hoofs. The samovar was disassembled when there was a necessity of removal(distance) of the rests of burning of wood and ashes.
Material, engineering: a brass, punching, the soldering, mount; wood, turning, tinning.
Capacity ~ 5,0 L.
Height: 420 mm. Width (in the widest part): 290 mm.
Condition - 9 points.
| |
|
ÐÓÑ ENG |
|
|
|
A samovar - teapot. "TEAPOT WITH THROUGH HOLE ". Tin. Collection. Antiques.
The manufacturer - a brand is absent.
Time of manufacturing: ~ the beginning of XIX century (it is possible - China or Tibet).
The body is of oval form. In the bottom part of the body perpendicularly axes the spout-handle the through aperture is executed. These apertures are intended for performance of function as ash-pit, from a cavity of the bottom part of the body ashes and the rests of burning of wood also taken away. At a level of the bottom cut of through apertures the steel (pig-iron) lattice which is carrying out a role of brazier is established. The spout is cast, tin in the form of the letter "S", narrowed to the termination(ending). The handle in a form of the letter "C" is made of a tin tube of round section and is weaved by a rod. On a tin demountable cover the wooden knob on the rack is established. The basis is soldered to the bottom part of the body as the truncated cone which the bottom part is closed by the soldered plate.
Material, engineering: tin, punching, chasing, soldering, mounting; weaving by a rod, turning.
Capacity ~ 0, 25 L.
Height: 165 mm. Width (in the widest part): 155 mm.
Condition - 8 points.
| |
|
ÐÓÑ ENG |
A samovar “Vase - a wine-glass with small kerosene tank ”, kerosene, “KEROSENE (BENZIN) “EDISON” with small kerosene tank ”. (the Branch of a collection - KEROSENE). Collection. Antiques.
The manufacturer - a brand on a face sheet of the body - the image of a heraldic shield, inside it from above - an octahedral star with the image of the mermaid with a small shield in her left and a sword in the right hand; to the left of a board the letter "M" - to the right of a board the letter "F"; in the middle of the shield the inscription - "EDISON" - PATENT - ¹ 22900 - is lower - WARSZ. - T.G. - NIKIEL; below a board âûáèòà figure " 1 ".
On the small kerosene tank the inscription on a metal strip - “ ORIGINAL - ENDERS - 9060 - is lower - PTB Nr. III B/E-3546 - MADE in GERMANY - below - NUR FUR BENZIN ”
Time of manufacturing: ~ last quarter of XIX century, probably, the beginning of XX century.
The body has a form of a wine-glass with interception in the top part. The crane is cast of the simple form with a pith key, with figured branch and wooden knob. Two lateral handles with semisphere bases and four horns bent up hold two cylindrical wooden handles, strapped outside by four screw-nuts. A ring is of the flat simple form. On a cover two wooden knobs on their posts and a unary stream-valve. The crown is of the simple form with figured cuts, is also soldered to a cover. The jug (an internal pipe) has the standard form; in the bottom and average parts of it there are located two soldered perpendicularly each other metal tubes. A choke is of simple form, with wooden knob on the rack.
High blew it is punched by vertical longitudinal cuts, employees also as observation windows, from lateral faces in the top part blew are executed by figured cuts for fastening by bayonet connection the body with the base. From the back party(side) of the blew is present a special cut for a tube of submission of fuel from tank to the mechanism of burning. Below punching blew on the neck of the base from the right side there is the place of fastening of the mechanism of burning by the soldering to the base of a samovar is located. Below, on a face surface of the neck of the base, the semicircular aperture for firing a kerosene (benzin) in the mechanism of burning is executed.
The mechanism of burning consists of a torch, similar to a torch of a kerosene stove, tank for kerosene (benzine) with the mechanism of a forcing of fuel (the piston pump) and the drainage valve.
Extending to it’s bottom the neck the base inseparable connected with the cast square base of a samovar. The metal hemisphere is soldered to in the bottom part of the base. Four legs of a samovar - cast ledges acting a lugs a little forward of the base.
Material, engineering: a brass, polishing, a stamp, the soldering, mount; a tree, turning; tinning. At restoration nickel plating is removed(taken off) from a surface and polishing of a samovar is made.
Capacity ~ 2,75 - 3,00 L.
Height: 415 mm.
Width (in the widest part): 300 õ 270 mm.
Condition - 8 points.
A place in a collection - ¹ 127.
| |
|
ÐÓÑ ENG |
A samovar “Vase in a form of egg – (yurta)”, “ VORONTSOV’s EASTER EGG”, nickelized. Collection. Antiques.
The manufacturer - a brand on a cover: from above - «ÔÀÁÐÈÊÀ ÒÎÂÀÐÈÙÅÑÒ. ÍÀÑËÚÄÍ. - on the centre - Í. - with the image of the Russian arms and a head (Nikolas II) - A. is lower than two prints of one medal - 1908 - below - âú ÒÓËÚ ».
Time of manufacturing: ~ the beginning of XX century.
The body is in a form of smooth egg - "þðòà". The crane of the cast complex(difficult) form with the basis - cast patterned washer with deciduous patterns and inflow for deduction tea-strainer on plum of the crane. The cone key is decorated by cast pattened branch and wooden quick. Two vertical wooden handles on their tacks are fastened by figured screw-nuts from below are established between four cast holders (two up and two below) of handles of a tendrils ornament of independent fastening to the body each. A circle is simple smooth. On a cover are established two wooden knobs on their posts. The boiler is of a complicated cast configuration fastened by two screws to a cover, from above on the hinge the folding cover of a boiler valve is established. A crown of the complex(difficult) form with figured cuts on its perimeter. Blew is absent. Below the rack of the body smoothly passes in ring form ledge, then below she(it) extends up to the circle connected to the round cast base. Ash-shut is of round form, on a loop, with the rotary handle - a latch, it is established on the bottom, demountable platform of the base. Four cast legs in a form of tendril figures are cast continuation of the base.
Material, engineering: a brass, nickel plating, punching, a stamp, moulding, the soldering, mount; a wood, turning, tinning.
Capacity ~ 2, 85 L.
Height: 380 mm.
Width (in the widest part): 300 mm.
Condition - 7 points (a choke is absent).
Place in a collection - ¹ 128.
| |
|
ÐÓÑ ENG |
À samovar - teapot. Silvered. Collection. Antiques.
The manufacturer - a brand is absent.
Time of manufacturing: ~ the third quarter of XIX century.
Samovar consists of three parts: - a demountable teapot, the basis and a spirit-lamp.
Teapot has the spherical form. The top part of a teapot completely mechanically decorated, from sides has two smooth decorative shields for an engraving on them monograms of the owner. A spout made in the form of the letter "S", narrowed to the termination(ending). On a direction of an axis of spout there are two soldered decorative, as oblong fishes, the holders of the handle of the teapot, separated from the handles by two bone washers of black color. The hinge is soldered to the top part of a teapot for fastening decorated cover with a boiler - an aperture and the metal figure handle.
The bottom part of a teapot smooth, without mechanical decoration of surfaces, oval in its the form, has four figured pins for installation of a teapot on the basis, soldered perpendicularly axes "spout-handle".
The basis has the form hollow bagel. The top part of the basis is mechanically decorated, bottom - smooth. Perpendicularly axes ” spout - handle ” to the basis are soldered two vertical metal ovals decorated by vignettes. On the top part of vertical ovals in special grooves the teapot is established. In an average central part of the basis there is a deepening for installation in it a spirit-lamp. Four decorative legs are soldered to the bottom part of the basis as paws of a predatory animal.
Spirit-lamp simple, round, with a detachable fuse with the central aperture for a match. A plug of spirit-lamp it is not stipulated.
Material, engineering: a brass, silvering, minting, a stamp, molding, the soldering, mount; a bone, turning; soldering.
Capacity ~ 3, 10 L.
Height: 410 mm.
Width (in the widest part): 240 mm.
Condition - 9 points.
Place in a collection - ¹ 129.
| |
|
ÐÓÑ ENG |
|
|
|
130. A samovar (Bulliotte) - a coffee pot. Silvered. Collection. Antiques.
The manufacturer - a brand on below of a teapot: « from above a circle - a double indistinct print: “SOUTHINGTON C. C. C.” - in a circle - from above - a double indistinct print: “QUANDRUPLE” - in the centre of a circle - balance with two bowls - below - a new brand are represented: “PLATE” - is lower than a circle - a double indistinct print: “COMPANY”, is even lower - a new brand: “2104”, the brand in two lines is lower: “MADE IN - U.S.AMERICA”.
Brand on the bottom side of the base – “2104”.
On one of the back sides of a teapot the monogram – “AS” is engraved.
Time of manufacturing: ~ the third quarter of XIX century.
Bulliotte consists of three parts: - a demountable teapot, the base and a spirit-lamp.
The teapot is of hexahedral forms, reminds the bottom half hexahedral spheres with the corners of sides raised up. The top part of a teapot and lateral surfaces hexahedron are decorated engraved by figure of flower subjects. Spout is in the form of the letter "S", narrowed to the termination(ending), round variable section and flat lateral sides. From the interior of a place of the soldering spout to a body of a teapot it is soldered a water-strainer. On a direction of an axis “spout – handle” two holders of the handle of the teapot are soldered, which are separated from the handle by bone washers of black color. The handle of a teapot simple, oval section. The hinge is soldered to the top part of a teapot for fastening a cover of hip form with a boiler - an aperture and the metal handle above. The surface of a cover is covered with the engraved pattern of flower subjects. That the cover of a teapot had horizontal fixing in the cast away position hardly above the hinge of a cover of a teapot the metal ledge is soldered. To the top part of a teapot, under the hinge, the metal probe as a half moon, serving by the bottom support for a cover of a teapot in the cast away position is soldered. The body of a teapot from hexahedral hemispheres form below it is smoothly narrowed up to round neck, and then, passes in hexahedral base of a teapot below. To flat surfaces of lateral faces hexahedral body of a teapot it is soldered four figured pins, on two each party(side), for installation of a teapot on the base.
The base has the form flat hexahedron with sides acting to middle before formation(education) of a ledge in the centre of the base with a round aperture - an adjusting place for a spirit-lamp. The surface of the basis is decorated with an engraving with figures of flower subjects. From two parties(sides) of a ledge of the base are soldered decorative under the form, but without an ornament, two holders of a teapot. On the top part of vertical holders in special grooves the teapot is established. A spirit-lamp simple form with the decorative handle, round, with a fuse as the separated mechanism of adjustment of intensity of a flame by means of increase - reduction of length of a match. Ô A small cap of spirit-lamps it is not stipulated.
Material, engineering: a brass, silvering, a stamp, moulding, the soldering, mount, a manual engraving; bone, turning; tin.
Capacity ~ 0, 80 L.
Height: 305 mm.
Condition - 9 points.
Width (in the widest part): 230 mm.
Place in a collection - - ¹ 130.
| |
|
ÐÓÑ ENG |
|
|
|
Samovar - "Dutch" - the seller asserted that a samovar is brought from Holland. Copper with brass elements of a design of a samovar and his decorative furnish. Collection. Antiques.
The manufacturer - a brand is absent.
Time of manufacturing: ~ the beginning of XIX century.
The body - looks like an ancient Greek amphora. The top part of the body has the cylindrical form, smoothly passes in egg-form of the bottom part. From above a cylindrical part is present acting lug, by step passing in a narrowed mouth of the body, decoratively trimmed with brass balls on perimeter of an aperture of a mouth.
On a mouth the copper cover with two wooden clamps on two brass posts is established. The cover is narrowed up, forming neck, then is higher spread as a bell, then again is narrowed, forming a mouth of the cover which in turn has decorative furnish from brass balls on perimeter of an aperture of a mouth.
On a cover it is established copper choke with rotating brass quick in a form as acorn, from the inside of the choke to which the figured bent plate overlapping two apertures of draft in the top part of the choke is attached.
Brass motionless holders of handles of a samovar look like the letter "C" with a figured thickening in the bottom part soldered to a cylindrical part of the body of a samovar from two sides. In the top part holders have hinge connection with a mobile part of the holder who is looking like stirrup in which horizontal part are established wooden figure-cylindrical clamps, keeping for which is for carrying out a samovar.
The crane is executed from a brass, has visas of a predatory bird with eyes from sides, plums looks like a beak of this bird, the key of the crane - a simple brass cone with flat wooden quick as the bird's tail. The patterned washer fastenings of the crane to the body is absent.
Bottom egg-form part of the body smoothly passes in a neck of the bases with six figured cuts blew, then by steps extending in the lowermost part has decorative furnish from brass balls on perimeter of an aperture of connection with the flat basis of a samovar.
The copper basis of a samovar of the square form with the narrow parties of a square going downwards, have rectangular dredging from each of the parties of the basis. On corners of the square basis are soldered brass knobs - carrying out a role of legs of a samovar.
The plate forming ash-pit of a samovar is soldered to an internal part of the basis convex from top to bottom. To this plate in the central part on hinge to a loop on rivets the cover of the ash-pit of a samovar, having rotating the handle - lock fastens.
The round lattice has four parallel iron rods.
The internal pipe (jug) yas a cone form.
Material, engineering: ìåäü, a brass, a stamp, moulding, the soldering, mount; a tree, turning; tin.
Capacity ~ 5, 00 L.
Height: 565 mm. Width (in the widest part): 310 mm.
Condition - 10 points. Place in a collection - ¹ 131.
| |
|
ÐÓÑ ENG |
|
|
|
Collection. Antiques.
The manufacturer - a brand (B.G.Tejle).
Time of manufacturing: ~ last quarter of XIX century. Probably, the beginning of XX century.
The body in a form of standard samovar jar with vertical fragments. The crane of the cast simple form with a pith key with figured branch and wooden quick. Two lateral handles with the ridge basis and four bent horns hold two cylindrical wooden handles, strapped outside by four robins. A circle a ridge ornament. On a cover two wooden knobs and a unary boiler; the ring of the simple form with vertical cuts, appropriate cuts of the blew. Choke with wooden knob, similar knobs on a cover. The basis - capacity for kerosene, the round form on four legs as lion's paws, the fuse closing a jellied mouth of the basis, is supplied with a drainage aperture. The body joins to the basis by the hooks mechanism of gearing. On the rack of the basis the mechanism of adjustment of a flame is established by promotion of a match. The observation port simultaneously is a window of ignition of a match, is supplied with mica, opens and fixed by the screw.
Material, engineering: a brass, polishing, a stamp, the soldering, mount; a tree, turning, tinning.
Capacity ~ 2,5 ë.
Height: 465 mm. Width (in the widest part): 290 mm.
Condition - 10 points.
| |
|
ÐÓÑ ENG |
|
|
|
Collection. Antiques.
The manufacturer - a brand on the basis - "E" and « WMF - G ».
The body - a sphere, with decorative belt on diameter. From sides of a sphere two holders of handles as lion's heads, in a mouth of each holder are established handles in a form of a ring. In the top part of the body the small circle of the simple form is made (as a ledge) on which the cover, under the form - continuation of a spherical body is established. On a cover the handle in a form of small sphere is established.
The crane is of the simple form, cast, has a key of the crane simple flat handle.
To the body from four parties(sides) - four decorated legs bent as the letter "S" are symmetrically soldered, in the bottom part – in the places of fastenings to the flat basis - are decorated as lion's paws.
The flat basis with dredging on four parties(sides) has four legs as spheres. In the middle of the basis on a small ledge the spirit-lamp with a hat and the mechanism of adjustment of intensity of a flame (an output(exit) of a match) is established. The bottom part of the body of the spirit-lamps is executed as twelve – sides form.
Material, engineering: a brass, polishing, chasing, a stamp, the soldering, mount, tinning, silvering.
Capacity ~ 2,5 l.
Height: 215 mm. Width (in the widest part): 210 mm.
Condition - 10 points.
| |
|
ÐÓÑ ENG |
|
|
|
Copper with some details made from bronze and tombac. Collection. Antiques.
The manufacturer - a brand is absent.
The body is in a form of a copper sphere, with decorative belt on diameter. Inside the body the pipe for the heated weight or ice is established. From sides of a sphere two holders of handles with apertures for installation in them of handles as rings (holders and rings are made from tombac) are established. In the top part of the body the small decorative circle is made (as a ledge) on which the cover, under the form - continuation of a sphere of the body is established. On the top part of a cover there is the brass ring ledge limiting ventilating punching, on the centre the brass handle as a small sphere is established.
The crane of the simple form, cast, is made from tombac, the brass key of the crane has simple handle as the letter "U" with bone quick the conic form.
To the bottom part of the body is joined also it is soldered bronze Hercules on his right knee, on two hands and on the basis of a neck holding the body - a sphere. On three carving pins are fastening Hercules to the square basis made from tombac. The flat basis has four legs as spheres on corners.
Material, engineering: copper, a brass, bronze, tombac, polishing, chasing, a stamp, the soldering, mount, tinning.
Capacity ~ 2,5 ë.
Height: 325 mm. Width (in the widest part): 200 mm.
Condition - 8 points (dents on the body and on a cover, is absent top choke of punched apertures).
| |
|
ÐÓÑ ENG |
|
|
|
Copper, brass. Collection. Antiques.
The manufacturer - a brand is absent (by elements of a cover it is possible to assume, that this vessel for fault was made in London).
Time of manufacturing: ~ the second - the third quarter of XIX century.
The body is of the complex(difficult) form - flat in an average part the copper sphere having in the top part expansion as a bell with simple ring. Inside the body the pipe for the heated weight or ice is established.
The crane of the brass cast complex(difficult) form with decorative strips with a arm - key with simple cylindrical bone quick.
From two parties(sides) of the body four copper decorative holders of handles are soldered. Four copper openwork lateral handles as the letter "S" (one - the bottom fastening to the body) horns upwards hold two cylindrical bone knobs of black color.
On a cover with the minted relief pattern, knobs and a boiler are absent. The decorative overlay as several leaves from above is established, above it(her) the cast copper demountable handle as decorated as a mushroom fastens.
The rack of the basis of the cylindrical form, narrowed in the average part, decorated by the belt and cylindrical cut lines, extends in the bottom part. Punched basis of the square form with dredging on four parties(sides) and deflexed edges(territories), on four legs - spheres.
Material, engineering: copper, a brass, chasing, a stamp, the soldering, mount; a bone, turning; tinning.
Capacity ~ 6,0 ë.
Height: 420 mm. Width (in the widest part): 380 mm.
Condition - 9 points (has broken off soldered edge of the cover).
| |
|
1-15 | 16-30 | 31-45 | 46-60 | 61-75 | 76-90 | 91-105 | 106-120 | 121-135 | 136-150
|
|