1-15 | 16-30 | 31-45 | 46-60 | 61-75 | 76-90 | 91-105 | 106-120 | 121-135 | 136-150

  61. Samovar “Vase in a form of a cup”, “ BALASHEV's GOBLET” ÐÓÑ  ENG  
Samovar “Vase in a form of a cup”, “ BALASHEV's GOBLET”, copper. Collection. Antique.
Manufacturer: trademark on a cover: at the left in a circle: «ÏÎI … ÎÌÑ. HONOUR» - in the center in a circle: «BROTHERS BALASHEV IN TULA»; on the right in a circle: "ÃÐÀÆÄÀÍß (CITIZEN)".
Manufacturing time: ~ the first quarter of XIX century.
Body – in a form of a cup (goblet).
Choke – simple configuration with wooden round knob on its post.
Crown –figure form with round cuttings.
Cover –punched simple form with two wooden round knobs on their posts and a steam exhaust valve.
Round – round and smooth.
Holders – cast, two with four vertical horns and patterned platform of each brazing to the body, with two figure wooden round handles, each between two horns, and on two tacks fastened by four figure screw-nuts on endings of tacks.
Crane – cast, , tombac, patterned form, with cone key and vertical patterned figure handle, with wooden round knob above.
Base – cast, round, in a form of hip.
Legs – patterned four, in a form of hoofs, lower part of the base, a little lug forward.
Ash-pit – no.
Ash-shut - round cover with catch, fastened by small hinge on the bottom of the base.
Stuff, technique: copper, tombac, chasing, caulking, punching, soldering, brazing, inner tinning, assembling; wood turning and cutting.
Capacity: ~ 2,5 litters.
Height: 410 mm. Width: 230 mm.
Restoration: the soldering of the crane with a key, manufacturing of a crown and choke, polishing, accessories.
Status: 9 marks.
  62. Samovar « Kitchen three-section with a tube », "POKROVSKY’s KITCHEN" ÐÓÑ  ENG  
Samovar « Kitchen three-section with a tube », "POKROVSKY’s KITCHEN", a brass. Kitchen three-section was used to prepare, for example, soup, kasha and boiling water for tea at once. Collection. Antique.
Manufacturer: trademark on the face side of the base “ ALEXANDER POKROVSKY in ÒULA”.
Manufacturing time: ~ first half XIX centuries.
Body – in a form of standard samovar pot. Inner capacity of the pot is divided in three chambers by three figure brass plates, hermetically soldered to the inner surface and inner heat pipe.
Choke – simple configuration with wooden round knob on its post.
Crown – figure form with patterned cuttings.
Cover – simple form with two wooden round knobs on their posts and a brass steam exhaust valve.
Round - simple and smooth.
Holders – cast, two, in a form of women ear-rings, with platform brazing to the body, with two round wooden handle on their tacks, fastened by four screw-nuts at endings of tacks.
Crane – cast, simple form with a spout in a form of high boot, with cone key and patterned figure handle with wooden round knob above.
Ash-pit – with patterned cuttings, not same as on the crown.
Base – cast, square, standard form.
Legs – patterned four, in a form of turned over mushrooms.
Ash-shut – round cover with catch, fastened by small hinge on the bottom of the base.
Stuff, technique: brass, chasing, caulking, punching, soldering, brazing, inner tinning, assembling; wood turning and cutting.
Capacity: ~ 5 litters.
Height: 370 mm., with tube: 610 mm. Width: 300 mm.
Restoration: there is no necessity.
Complete set of this samovar consists of: samovar and tube (removable chimney) for draw with wooden handle attached at the middle part of tube.
Status: 10 marks.
  63. Samovar “Vase, rolling made jug”, “ROLLING MADE JUG” ÐÓÑ  ENG  
Samovar “Vase, rolling made jug”, “ROLLING MADE JUG”, tombac. In “ the Price-list of company steam samovar factory of successors of V.S.Batashev in Òula ” the same samovar is located under ¹ 32”.Collection. Antique.
Manufacturer: trademark on a cover: “the Arms of Russia - lower – « Charter approved by Imperator on April 10th, 1898 ». Below - two images of a bronze medal of Alexander II from 1870ã. - an inscription: “Company of steam samovar factory of of SUCCESSORS of Vasily Stepanovich BATASHEV in Tula” - more to the right - two images of a gold medal of Alexander III from 1882ã.
Trademark on a face side of the body - « Charter approved by Imperator on April 10th, 1898 », “Company of steam samovar factory of SUCCESSORS of V.S.BATASHEV in Tula”.Manufacturing time: ~ last quarter of XIX century.
Body – in a form of vertical rhombus, on which perimeter of a circle concave-convex shares.
Choke – simple configuration with wooden round knob on its post.
Crown – cast, figure form with patterned cuttings and with patterned upper ring.
Cover – simple form with two wooden round knobs on their posts and a steam exhaust valve.
Round - cast, figure and patterned.
Holders – four, cast, like four vertical patterned openwork horns and patterned platform of each brazing to the body, with two figure wooden round handles, each between two horns, and on two tacks fastened by four figure screw-nuts on endings of tacks.
Crane – cast, patterned form, with cone key and patterned figure handle with wooden round knob above.
Ash-pit – with patterned cuttings, the same as on the crown.
Base – cast, square, with square rectangular lug a little forward on each side of the base.
Legs – patterned four, lower part of the base, a little lug forward.
Ash-shut – round cover with catch, fastened by small hinge on the bottom of the base.
Stuff, technique: tombac, chasing, caulking, punching, soldering, brazing, inner tinning, assembling; wood turning and cutting.
Capacity: ~ 10 litters.
Height: 550 mm. Width: 380 mm.
Restoration: there is no necessity.
Status: 10 marks.

  64. Samovar “Vase in a form of a sphere with high ash-pit”, “HIGH ASH-PIT SPHERE” ÐÓÑ  ENG  
Samovar “Vase in a form of a sphere with high ash-pit”, “HIGH ASH-PIT SPHERE”, nickel-plated brass. Collection. Antique.
Manufacturer: trademark on a cover: in a circle points - the Arms of Russia - lower rubbed an inscription - below - two images of one medal with an inscription from above: "1866" - in the center - "Ô" - lower - « BATASHEV Br.» on the right - two images of a medal - from above: "1857".
Manufacturing time: ~ third quarter of XIX century.
Body – in a form of sphere with transition in six conic concentric circles in the bottom part.
Choke – simple configuration with wooden round knob on its post.
Crown – figure form with patterned cuttings, with soldered upper disc for teapot.
Cover – simple form with two wooden round knobs on their posts and a steam exhaust valve.
Round - simple and smooth.
Holders – four, direct lateral horns up, a corrugated platform everyone fastens to the body, in pairs hold on tacks two cylindrical wooden handle, strapped at endings of tacks by four screw-nuts.
Crane – cast with a spout as a duck with convex eyes; with a cone key and figured handle with wooden knob above.
Ash-pit – patterned cuttings, similar the cuttings on the crown, which made on all surface of high cone post of the base.
Base – cast, square.
Legs – four, in a form of turned over mushrooms at corners of the base.
Ash-shut – round cover with catch, fastened by small hinge on the bottom of the base.
Stuff, technique: nickel-plated brass, chasing, caulking, punching, soldering, brazing, inner tinning, assembling; wood turning and cutting.
Capacity: ~ 7 litters.
Height: 480 mm. Width: 370 mm.
Restoration: there is no necessity.
Status: 7 marks.
  65. Samovar “Travelling (picnic) samovar ”, “TEAPOT” ÐÓÑ  ENG  
Samovar “Travelling (picnic) samovar ”, “TEAPOT”, brass. Collection. Antique.
Manufacturer: trademark on the bottom: from above – six-pointed star, in the center three crossed hammers in a frame of a horseshoe, from below - upwards - an ornament. Below – print of the figure “2”. (In A.A.Lobanov's catalogue the analogue of this samovar is located under ¹ 75.)
Manufacturing time: ~ middle of XIX century.
Body – smooth oval.
Choke – two, first of heat pipe - simple configuration with wooden round knob on its post, the second – of water bell mouth – triangle configuration with wooden round knob on its post.
Crown – no by design.
Cover – no by design.
Round - no by design.
Holders – one on the rear part of the body, made of a strip of a brass with inner bent edges, covered by willow osier, and soldered to the body in its top and average parts.
Crane – cast, in the form of the letter “S” with two convex belts in an average part; narrowed spout has to the ending a long horizontal part.
Ash-pit – patterned cuttings on the ash-shut.
Base – no by design.
Legs – four, cast, curved as a letter “S”, soldered to the bottom of the body.
Ash-shut – in a of cylinder cup with patterned openwork cuttings, soldered to the bottom of the body.
Stuff, technique: brass, chasing, caulking, punching, soldering, brazing, inner tinning, assembling; wood turning and cutting.
Capacity: ~ 2,5-3,0 litters.
Height: 290 mm. Width: 390 mm.
Restoration: there is no necessity.
Status: 8 marks.
  66. Samovar “Vase in a form of pear”, “SOUVENIR” ÐÓÑ  ENG  
Samovar “Vase in a form of pear”, “SOUVENIR”. The working model of a samovar, souvenir, with enamel. Copper. Collection. Antique.
Manufacturer: trademark is absent .
Manufacturing time: ~ third quarter of XIX century.
Body – in a form of pear. All surface covered by enamel with flower and green leaves portrayals.
Choke – punched, simple form, with a knob in a form of cast cock.
Crown – punched, simple form, with enamel.
Cover – punched, simple form, with enamel and with two ivory knobs on their posts, without a steam exhaust valve.
Round – simple, smooth.
Holders – two, with enamel, curved as letter “U”, with two ivory handles on tacks, fastened by four screw-nuts on endings of tacks. Both holders strapped to the body by screws and screw-nuts, then soldered.
Crane – cast, simple form, with a cone key and figured handle with ivory knob above.
Ash-pit – no.
Base – punched, square, with four endings on corners as legs. The post of the base narrowed in middle part, with enamel.
Ash-shut – no.
Stuff, technique: copper, chasing, caulking, punching, soldering, brazing, inner tinning, assembling; ivory turning and cutting.
Capacity: ~ 0,150 litters.
Height: 150 mm. Width: 115 mm.
Restoration: there is no necessity.
Status: 10 marks.
  67. Samovar “Vase in a form doubled cone”, “SHESTOPALOV’s KEROSENE SAMOVAR” ÐÓÑ  ENG  
Samovar “Vase in a form doubled cone”, “SHESTOPALOV’s KEROSENE SAMOVAR”, nickel-plated brass. “Component part of collection branch - kerosene samovars”. Collection. Antique.
Manufacturer: trademark on a cover: at the left in a circle: « security patent ¹ 53834 »; in the centór - « A. D. SHESTOPALOV TULA »; on the right in a circle: « security patent ¹ 53834 ».
Manufacturing time: ~ last quarter of XIX century. Probably, the beginning of XX century.
Body – in a form of two sharp part of cones entered each other, the bottom of the body has rounded form.
Choke – punched, simple configuration with ivory round knob on its post.
Crown – figure form with patterned cuttings, soldered to the cover.
Cover – punched, simple form with two ivory round knobs on their posts and a steam exhaust valve.
Round - simple and smooth.
Holders – cast, two Byzantian vertical patterned, each consists of two nickel-plated holders (upper and lower) and figure ivory handle between them on tack with screw-nut fastened ending of tack at bottom. Four platforms of two holders are brazing to the body.
Crane – cast, of simple form, with a cone key and openwork handle in a form of two rounded goat horns.
Ash-pit – on cone part of the post of the base as several rings of round holes.
Base – round tin for kerosene, with drain hole, with metallic jam with round ivory knob on its post. Arm of flame adjusting mechanism by removing wick is situated at the bottom of the base. The upper part of the post of the base bayoneted to the bottom of the body.
Legs – eight, rounded, bottom convex part of the base.
Ash-shut – not provided by design.
Stuff, technique: nickel-plated brass, nickel plating, chasing, caulking, punching, soldering, brazing, tinning, assembling; wick, ivory turning and cutting.
Capacity: ~ 2,5 litters.
Height: 330 mm. Width: 185 mm.
Restoration: there is no necessity.
Status: 9 marks.
  68. Samovar “Vase with medallions, without ash-pit”, “SOMOV BROTHERS ” ÐÓÑ  ENG  
Samovar “Vase with medallions, without ash-pit”, “SOMOV BROTHERS ”, tombac. Collection. Antique.
Manufacturer: trademark on a face side of the base: from above «IN TULA», on the center: two images of a medal - « For hard-working and craftsmanship 1861 »; « ALEXAN. II imper.(ator) and Tsar of All-Russia», - lower: « SOMOV BROTHER’s HANDICRAFT».
Manufacturing time: ~ third quarter of XIX century.
Body – vase with medallions, without ash-pit.
Choke – simple configuration with wooden round knob on its post.
Crown – figure form with patterned cuttings.
Cover – simple form with two wooden round knobs on their posts and a steam exhaust valve.
Round - cast and patterned.
Holders – cast, two, each with two vertical horns and patterned platform of brazing to the body, with figure wooden round handle, each between two horns, and on tack fastened by two figure screw-nuts on endings of tack.
Crane – cast, patterned form, with cone key and patterned openwork figure handle, with wooden round knob above.
Base – cast, square. Post of the base is high, smooth, a little cone, without ash-pit.
Legs – four, in a form of turned over mushrooms at corners of the base, fastened to an additional bottom plate of the base.
Ash-shut – round cover with catch, fastened by small hinge to an additional bottom plate of the base.
Stuff, technique: tombac, chasing, caulking, punching, soldering, brazing, tinning, assembling; wood turning and cutting.
Capacity: ~ 5 litters.
Height: 410 mm. Width: 330 mm.
Restoration: there is no necessity.
Status: 9 marks.
  69. Samovar “Vase in a form of a saucepan”, “LIUBIMOVA’s SAUCEPAN” ÐÓÑ  ENG  
Samovar “Vase in a form of a saucepan”, “LIUBIMOVA’s SAUCEPAN”, nickel-plated brass. “Component part of collection branch - SAUCEPANS”. Collection. Antique.
Manufacturer: trademark on a face side of the base: « V.N.LIUBIMOVA’s PLANT».
Manufacturing time: ~ middle of XIX century.
Body – of standard samovar form of a saucepan. The cylindrical middle part of the body at upper and at bottom part become some wide, developing two rims – the upper, becoming a round, the lower also cylindrical, and all together forming a classic samovar’s body - a saucepan.
Choke – simple configuration with wooden round knob on its post.
Crown – figure form with patterned cuttings.
Cover – simple form with two wooden round knobs on their posts and a steam exhaust valve in a form of duck.
Round - simple and smooth.
Holders – cast, two, each with two vertical horns and patterned platform of brazing to the body, with figure wooden round handle, between two horns, and on tack fastened by two figure screw-nuts on endings of tack.
Crane – cast, simple form, with cone key and patterned openwork figure handle, with wooden round knob above.
Ash-pit - with patterned cuttings, the same as on the crown.
Base – cast, square. Post of the base is narrowed in the middle part.
Legs – four, lower endings of the base.
Ash-shut – round cover with catch, fastened by small hinge to the bottom of the base.
Stuff, technique: nickel-plated brass, nickel plating, chasing, caulking, punching, soldering, brazing, tinning, assembling; wick, wood turning and cutting.
Capacity: ~ 1,25 litters.
Height: 330 mm. Width: 250 mm.
Restoration: there is no necessity.
Status: 6 marks.
  70. Samovar “Vase in a form of high a jug”, “EAST JUG” ÐÓÑ  ENG  
Samovar “Vase in a form of high a jug”, “EAST JUG”, tin-plated copper, with engraving elements, grey in colour by ancient oxide. Collection. Antique.
Manufacturer: is unknown. Such samovars were made on Ural factories for purchasing in Middle Asia region.
Manufacturing time: ~ the second quarter of XIX century.
Body – in the form of high, narrowed up jug, with convex fragments, with engraving elements, all detachable parts of jug are joined to the body by brass chain.
Choke – in a form of a hip, with a round knob above, with a chain joined to it.
Crown – no by design.
Cover – in a form of tube, with ring soldered to it for chain.
Round – simple smooth.
Holder – as pipe, slightly bent, with an engraving ornaments, soldered to the body in two points, with ring soldered to it for chain.
Crane – cast, with an engraving ornaments, a spout become thicker.
Ash-pit – patterned cuttings on the base.
Base – in a cone form, with patterned cuttings.
Legs – no by design, the jug stand on the bottom of the base.
Ash-shut – no by design. Ash falls on the ground.
Stuff, technique: tin-plated copper, inner tinning, chasing, caulking, punching, soldering, brazing, assembling, engraving.
Capacity: ~ 4,5-5 litters.
Height: 585 mm. Width: 180 mm.
Restoration: there is no necessity.
Status: 9 marks.
  71. Samovar as a coffee pot, “Coffee pot – “WASP” ÐÓÑ  ENG  
Samovar as a coffee pot, “Coffee pot – “WASP”, silver-plated, covered by black oxide. “Component part of collection branch – COFFEE POTS”. Collection. Antique.
Manufacturer: trademark on the bottom of the body«PLATED» and «Fraget w Warszawie».
Manufacturing time: ~ the end of XIX century.
Body – on a design reminds a cylindrical body of wasp - two cylindrical capacities having in an average part a narrow waist. In front of capacity are connected among themselves by a drainage tube of small diameter. A cylindrical perforated container for just-milled coffee on the figure pipe, with its thick metal base on the other end is into the body (two cylindrical capacities).
Choke – punched, simple form of hip, with round wooden knob on its post.
Crown – no by design.
Cover –simple form of pipe.
Round – simple and smooth.
Holders – two lateral holders with two horns up each, everyone of independent brazing to the body by the semicircular platforms, hold two cylindrical wooden handles, each on the tack , strapped outside by screw-nuts.
Crane – cast, simple form with spout and a horn on the end of it for coffee/water-strainer; with a cone key with figured wooden branch above.
Ash-pit – no by design.
Base – two smooth rings soldered to three legs on upper and middle part of them. A cylindrical spirit lamp with a wick mounted on the ring soldered to the middle part of legs.
Legs – cast, three, curved as letter “S”.
Ash-shut – no by design.
Stuff, technique: silver-plated copper, inner silvering, chasing, caulking, punching, soldering, brazing, assembling; wick, wood turning and cutting.
Capacity: ~ 0,45 litter.
Height: 310 mm. Width: 120 mm.
Restoration: there is no necessity.
Status: 9 marks.
  72. Samovar “Vase in a form of pot”, “LARGE POT” ÐÓÑ  ENG  
Samovar “Vase in a form of pot”, “LARGE POT”, nickel –plated brass. Collection. Antique.
Manufacturer: trademark is rubbed.
Manufacturing time: ~ last quarter of XIX century.
Body – in a form of standard samovar pot with interception in the top part.
Choke – simple configuration with wooden round knob on its post.
Crown – figure form with patterned cuttings.
Cover – simple form with high convex bulged neck and with two horizontal wooden round knobs on their four posts and on their tacks with screw-nuts on endings of tacks and a steam exhaust valve.
Round - simple and smooth.
Holders – four openwork patterned pieces (so called – dolphins) with a platform of each brazing to the body by it, with two wooden round handles, each between two holders and on two tacks fastened by four figure screw-nuts on endings of tacks.
Crane – cast, simple form, with cone key and patterned openwork figure handle.
Ash-pit - with patterned cuttings, the same as on the crown.
Base – cast, square, with square rectangular lug a little forward on each side of the base. Post of the base is narrowed in the middle part.
Legs – patterned four, lug a little forward, lower endings of the base.
Ash-shut – round cover with catch, fastened by small hinge to the bottom of the base.
Stuff, technique: nickel-plated brass, nickel plating, chasing, caulking, punching, soldering, brazing, tinning, assembling; wick, wood turning and cutting.
Capacity: ~ 15 litters.
Height: 670 mm. Width: 450 mm.
Restoration: there is no necessity.
Status: 10 marks.
  73. Samovar “Vase in a form of a saucepan”, “MALAKHOVTSEV’s SAUCEPAN” ÐÓÑ  ENG  
Samovar “Vase in a form of a saucepan”, “MALAKHOVTSEV’s SAUCEPAN”, brass. “Component part of collection branch - SAUCEPANS”. Collection. Antique.
Manufacturer: trademark on a face side of the base: at the left the arms worth lion, from above the maiden with wings, on the right a horse - unicorn, in the center of the arms an inscription is represented: “FACTORY VASILIJA ANDREEVICHA MALAHOVTSEVA V TULE” - is lower - IS AUTHORIZED BY GOVERNMENT - below - 1899 ». On a cover a brand is rubbed.
Manufacturing time: ~ third quarter of XIX century.
Body – of standard samovar form of a saucepan. The cylindrical middle part of the body at upper and at bottom part become some wide, developing two rims – the upper, becoming a round, the lower also cylindrical, and all together forming a classic samovar’s body - a saucepan.
Choke – simple configuration with wooden round knob on its post.
Crown – figure form with patterned cuttings.
Cover – punched simple form with two wooden round knobs on their posts and a steam exhaust valve.
Round - simple and smooth.
Holders – cast, two, each with two vertical horns and patterned platform of brazing to the body, with figure wooden round handle, between two horns, and on tack fastened by two figure screw-nuts on endings of tack.
Crane – cast, simple form, with cone key and patterned openwork figure handle, with wooden round knob above.
Ash-pit - with patterned cuttings, the same as on the crown.
Base – cast, square. Post of the base is narrowed in the middle part.
Legs – four, lower endings of the base.
Ash-shut – round cover with catch, fastened by small hinge to the bottom of the base.
Stuff, technique: brass, chasing, caulking, punching, soldering, brazing, tinning, assembling; wick, wood turning and cutting.
Capacity: ~ 3 litters.
Height: 415 mm. Width: 290 mm.
Restoration: there is no necessity.
Status: 5 marks.
  74. Samovar - coffee pot ÐÓÑ  ENG  
Samovar - coffee pot. Nickel- plated brass. Collection. Antiques.
Manufacturer: trademark is absent. (Presumably - «Fraget w Warszawie».
Manufacturing time: ~ presumably, the end of XIX century.
Body – cylindrical form, consists of two about equal the cavities divided(shared) by a horizontal partition, simultaneously intended for installation in it(her) of the cylindrical container for coffee. The bottom cavity of the body is intended for accommodation in it(her) of water, and after her(it) heating - boiled water; the top cavity serves for accommodation of the container with ground coffee and for preparing coffee boiled water of a condensate and the boiled water submitted on a tube from the bottom cavity. The container for coffee represents punched many apertures of small diameter the cylinder, with a cover bayoneted with the case of the container. The cover of the container has the drainage tube soldered on the center. The cylinder of the container fastened to the wire skeleton. Two lateral loops keep the body on the probes established from two parties(sides) of an average part of the metal holder of the body (and simultaneously carrying out function of the handle for transportation a coffee pot), looking like an arch (turned over letter “U”).
Choke – no by design.
Crown – no by design.
Cover – punched, simple form with one wooden round knob on its post and a steam exhaust hole.
Round - simple and smooth.
Holders – an arch is a holder.
Crane – cast, simple form with spout of a square structure and a cone key with horizontal wooden handle.
Ash-pit – no by design.
Base – round, step by step towering to a half-ohm to the center inside of which the spirit-lamp with metal handle – as ring and folding cover-hip with the arm – as a counterbalance is established. On a face sheet of the basis the holder of the terminator as lyre on the small rack and the terminator of an inclination of the body as a long metal arch with a ball on branch on the horizontal crossbeam established(installed) in apertures of horns of lyre is established.
Legs – no by design.
Ash-shut – no by design.
Stuff, technique: nickel-plated brass, nickel plating, chasing, caulking, punching, soldering, brazing, tinning, assembling; wick, wood turning and cutting.
Capacity: ~ 3 litters.
Height: 415 mm. Width: 215 mm.
Restoration: there is no necessity.
Status: 7 marks.
  75. Samovar - coffee pot, “Coffee pot – “BUMBLEBEE” ÐÓÑ  ENG  
Samovar - coffee pot, “Coffee pot – “BUMBLEBEE”, silver-plated, covered by light oxide. “Component part of collection branch – COFFEE POTS”. Collection. Antique.
Manufacturer: a brand on the bottom of the body «PLATED» and «FRAGET W WARSZAWIE».
Manufacturing time: ~ the end of XIX century.
Body – on a design reminds a cylindrical body of wasp - two cylindrical capacities having in an average part a narrow waist. In front of capacity are connected among themselves by a drainage tube of small diameter. A cylindrical perforated container for just-milled coffee on the figure pipe, with its thick metal base on the other end is into the body (two cylindrical capacities).
Choke – punched, simple form of hip, with round wooden knob on its post.
Crown – no by design.
Cover –simple form of pipe.
Round – simple and smooth.
Holders – two lateral holders with two horns up each, everyone of independent brazing to the body by the semicircular platforms, hold two cylindrical wooden handles, each on the tack , strapped outside by screw-nuts.
Crane – cast, simple form with spout and a horn on the end of it for coffee/water-strainer; with a cone key with flat figured wooden branch above.
Ash-pit – no by design.
Base – two smooth rings soldered to three legs on upper and middle part of them. A cylindrical spirit lamp with a wick mounted on the ring soldered to the middle part of legs.
Legs – cast, three, curved as letter “S”.
Ash-shut – no by design.
Stuff, technique: silver-plated copper, inner silvering, chasing, caulking, punching, soldering, brazing, assembling; wick, wood turning and cutting.
Capacity: ~ 0,85 litter.
Height: 375 mm. Width: 130 mm.
Restoration: there is no necessity.
Status: 9 marks.
1-15 | 16-30 | 31-45 | 46-60 | 61-75 | 76-90 | 91-105 | 106-120 | 121-135 | 136-150